Quick Installer Replace 5041 5041A axle seal installer tool kit with 18.5in connected rod, 2-fix-adapters. For stuck the front axle seal into the disconnect axle small cavity. Specific Usage Use this tool to install front axle seals into Dana models 44 and 60 and disconnect axles to their proper depth. Also used with ST-234 / 8409, 8411, 8415, 8416, 8417A & 8834 Seal Installers adapters. Advantage Simply removed the hub with the axle, punched out the old seal, and used this to install the new seal. No need to remove the intermediate shaft, there was plenty of clearance and this tool made light work of the whole job. It is difficult for you to do the same job by using conventional seal drivers and hammers. Please Note If you are working on AAM (American Axle Manufacturing) with a 9-1/4 14 bolt cover, you will need tool 8885B instead. You probably can’t do the job unless you purchase additional adapter pieces. Premium Materials Made from quality heavy-duty steel for strength and durability for years of use. Package includes 5041-1 Installer, 5041-2 Forcing Screw, 5041-3 Disc, 5041-7, and instruction. Installation 1. Install the front axle seal first, then insert the tool from the outside of the front axle. 2. Fully assemble the tool. 3. Tighten the nut with a wrench to push the seal into the correct position. 4. After the seal is installed, remove the tools. （Note: for reference only; Plz refer to your actual operation） Package Includes: 5041A Front Axle Seal Installer Tool
Fitment 1x Durable Small Engine Valve Spring Compressor, designed to works on Springs 3/4″ to 1-1/16″. Fit for Briggs and Stratton, Clinton, Harley-Davidson & More Engine. Replace for Part Number 23300. High Performance This engine valve compressor is a “MUST HAVE” to help you safely and easily remove engine valves without removing the cylinder head. Used to compress cylinder valve springs in order to remove and install their locks or retainers, and to replace valve stem seals or broken springs on internal combustion engines. Easy and quick to operate, saving time and effort. Superior Material The small engine valve spring compressor is made of premium steel and plastic, heavy duty steel construction for durability and long lifespan. Anti-rust, wear and corrosion resistance, professional manufacture, no deformation. What You Will Get 1x Small Engine Valve Spring Compressor (Comes with 1x larger jaw and 1x small jaw ).
Alternative to W470589001500. Precise Made with Oem Data and Directly Replac. 1pc Tdc Locating Pin. A Must Tool for Camshaft Timing Verification, When the Clutch Is Removed, the Timing Pin Is Get Inserted into the Crankshaft Position Sensor Hole in the Flywheel Housing and Engage into the Flywheel Notch.
For Detroit Diesel DD15. 1- TDC Locating Pin. 1- Crankshaft TDC Locating Tool. 1- Idler 3 Cantilever Tool. A set of Camshaft Timing Tools. 1- Engine Barring Tool (Turning tool). I’ll get back to you as soon as I can.
Includes 3162993, 3163056, 3033627, 3896790, and 3279794. Fits for Cummins Signature ISX QSX diesel truck engine, do not work on ISX12 or ISX15, for those you will need 4918991(not supplied). This kit allows the seal to be properly positioned on the crank nose to the front cover.
Compatibility: Specifically designed to separate quick connect fittings on 3/4″ heater lines for GM Vehicles. Features: Using this quick connect tool can disconnect the line without removing the clip. Improve your maintenance efficiency. The teeth of the tool fit well into tight tolerance of the connectors and when rotated allow the line to be pulled without damage to the connector or retaining clip, can be reused Quick Release Tool: Place the Heater Hose Disconnect in the line, slide it over the fitting, and pull it out to release the fitting. Superior Material: Made of aluminum alloy material, which is anti-rust, wearable, durable, and scratch-resistant for long lasting life Flexible & Easy to Use: This 39190 Heater Hose Disconnect allows you to connect and release tubing easily and quickly. Hinge design allows tool to slide over heater hose, even in tight spaces. How to Install: 1. Put the tool over the hose. 2. Close the tool opening to clamp the hose. 3. Push the tool towards the connector. 4. Pull on the line and remove the connector Package Includes: 1pcs 39190 Heater Hose Disconnect
1 Cummins Engine Barring/Rotating Tool. This Tool Fits the Flex Plate Teeth Perfectly, and Its Load-bearing Collar Provides Friction-free Operation While Rotating the Tool in the Housing – Rotating the Engine Is so Easy.
